Set the laptop and wireless display to the same refresh rate first, because Windows documents mismatched refresh rates as a cause of video stalling or freezing over Miracast.^1^
Correct the freezing
While connected to the TV:
- Open Settings > System > Display > Advanced display.
- Select the laptop display and note its refresh rate.
- Select the wireless TV display.
- Under Choose a refresh rate, select the same rate—typically 60 Hz if offered.
- Disconnect and reconnect with Windows key + K, then test both Duplicate and Extend modes.
The available rates depend on what each display supports; selecting a rate marked with an asterisk can also change the resolution.^2^
Verify both driver paths actually advertise Miracast support
Because the Wi-Fi, TV firmware, pairing records, firewall rules, and several driver versions have already been tested, do not repeat those changes yet. Run this on each laptop in Command Prompt:
netsh wlan show driver
netsh wlan show wirelesscapabilities
Check for:
Wireless Display Supported: Yes
(Graphics Driver: Yes, Wi-Fi Driver: Yes)
Also check that both WDI Version (Windows) and WDI Version (IHV) are nonzero. Microsoft documents these outputs as checks for Miracast support from both the graphics and Wi-Fi drivers.^3^
Interpret the results as follows:
- Graphics Driver: No — investigate the GPU driver path.
- Wi-Fi Driver: No or zero WDI versions — investigate the WLAN driver/adapter path.
- Both Yes on both laptops — receiver interoperability or the wireless environment becomes more likely, but this still does not prove which component failed.
Isolate the failing combination
Test all four combinations and record whether each one connects and remains stable:
| Source |
Samsung TV |
LG TV |
| Lenovo laptop |
Result |
Result |
| Dell laptop |
Result |
Result |
This distinguishes the next owner:
- One laptop fails with both TVs: focus on that laptop’s Wi-Fi/GPU path.
- Both laptops fail with only one TV: focus on that TV’s Miracast implementation.
- Every pairing fails in the same location but works elsewhere: investigate local wireless congestion or channel behavior.
- All combinations fail intermittently: capture logs during the failure rather than continuing to swap drivers.
Miracast interoperability depends on successful Wi-Fi Direct discovery, pairing, and reconnect behavior across both the source and receiver implementations.^4^
Capture the actual connection-stage failure
Immediately after Unable to connect:
- Press Windows key + R, enter
eventvwr.msc, and select OK.
- Open Applications and Services Logs > Microsoft > Windows > WLAN-AutoConfig > Operational.
- Find events at the exact connection-attempt time.
- Save the relevant events with Save Selected Events.
- Compare the event IDs and messages between the Lenovo and Dell.
Microsoft identifies WLAN-AutoConfig as the Windows event log containing Miracast connection information; its errors can show where the connection fails.^5^
Business-managed laptop check
If either Windows 11 Pro laptop is domain-joined or managed by organizational policy:
- Press Windows key + R, run
rsop.msc.
- Review Computer Configuration > Windows Settings > Security Settings > Wireless Network (IEEE 802.11) Policies.
- Open the applied wireless policy and inspect Network Permissions.
- Have the administrator verify that creating user wireless profiles is permitted.
This branch applies only to managed/domain-joined devices; Group Policy can otherwise block Miracast-related wireless behavior.^5^
If matching refresh rates resolves the freeze but connection failures remain, the WLAN-AutoConfig events and four-device test matrix are the useful evidence to give Lenovo, Dell, Samsung, or LG support. If no stable TV/laptop pairing exists, HDMI is the dependable alternative; Microsoft’s standard Windows repair guidance otherwise consists mainly of capability, Wi-Fi, firmware/driver, restart, and device-removal checks, most of which have already been completed.^6^
References
- Video playback settings in Windows | Microsoft Support
- [Windows 11](https://support.microsoft.com/windows/hardware/display-graphics/change-the-refresh-rate-on-your-monitor-in-windows#to-change-the-refresh-rate)
- Miscellaneous technical details and validation
- Validating your implementation
- Troubleshoot display projection to Surface Hub
- [Windows 11](https://support.microsoft.com/windows/hardware/display-graphics/fix-connections-to-wireless-displays-or-docks-in-windows)