Is there any way to fix Windows Defender Threat Service from crashing?

Joanne 40 Reputation points
2026-08-18T09:30:11.9833333+00:00

Hello everyone,

This morning I've been dealing with Windows Defender trying to scan my laptop for viruses after downloading a dataset on an academic project of my master's. While scanning, I got the following error message, I am in fear of getting a virus just by a service malfunctioning.

User's image

This happens every time I am trying to restart Windows Defender service.

Checked services.msc and Windows Defender Antivirus Service is set to 'Running' and 'Automatic'. While right-clicking on the service. all options are greyed out by constantly getting it to start.

User's image

In the meantime, I also get a 'your IT administrator' message or something I can't recall at the moment. I did nothing wrong, just troubleshooting a service that crashes.

Microsoft Defender service crashes near the end of the scan.

What I have done so far:

  • restarted laptop, same issue to no avail
  • scanning via the Terminal on DISM and SFC scans, both completed successfully
  • killed Windows Security window via Task Manager
  • got Windows Defender service run via services.msc (this is what caused the graying out of the operations in services window)
  • 'restarted' Windows Defender service multiple times while trying to scan laptop for viruses
  • attempted full scan, no results yet

After completing all these, the only solution is turning to a third-party antivirus as it's a dead end in my case. However, a third party antivirus may cause my laptop to overheat and conflict with Windows Defender.

Any help or feedback are greatly appreciated, thank you in advance!

Microsoft Security | Microsoft Defender | Other

Locked Question. You can vote on whether it's helpful, but you can't add comments or replies or follow the question.

3 answers

Sort by: Most helpful
  1. J 1 5 Reputation points
    2026-08-19T07:26:26.3533333+00:00

    I have just updated, ran a quick scan, worked fine, no issues.

    I'm hoping it has been resolved, thank you Microsoft.

    Intelligence version is....1.457.239.0

    Was this answer helpful?

    7 people found this answer helpful.
  2. Dunno 0 Reputation points
    2026-11-18T16:00:07.62+00:00

    I had an issue for weeks where a full scan would almost always crash defender and I got the same message. I went through every possible step you could think of and even went through two levels of Microsoft technical support but we couldn’t fix it. Multiple reinstalls, powershell commands, clearing cache manually, removing and updating signatures, literally nothing.

    I had one last brain wave yesterday and decided to reset my BIOS. I had a mild undervolt, power limit and some small tweaks like disabling enhanced turbo boost. This itself causes no issue during normal use including heavy gaming sessions.

    Once I reset the bios I went back in and used MSI Secure Erase+ to completely wipe the NVME drive. This method is better than just deleting partitions in the windows set up but not as overkill as the clean all command which is unnecessary. Then I booted into a Windows ISO via USB and reinstalled Windows once again. I have not had any further issues since, all scans completed successfully.

    I cannot be sure if it was the drive clean or the BIOS reset to default, but I’d lean on it being the BIOS. Full scans can hammer your CPU and it perhaps showed a borderline instability in my undervolt.

    Regardless of what fixed it, one of these two actions fixed it. I hope this helps someone.

    Was this answer helpful?

    0 comments No comments
  3. AI answer

    2026-08-18T09:30:44.3533333+00:00

    Yes. Based on the symptoms, the best supported path is to verify Defender components, remove any conflicting antivirus, then reset the Defender engine and platform.

    1. Check Defender services in an elevated PowerShell window:
    Get-Service WinDefend, WdBoot, WdFilter, WdNisSvc, WdNisDrv, SecurityHealthService, wscsvc | Format-Table -Auto DisplayName, Name, StartType, Status
    

    Expected state includes:

    • WinDefend = Automatic, Running
    • SecurityHealthService = Manual, Running
    • wscsvc = Automatic, Running
    • WdFilter = Boot, Running
    • WdBoot can be Stopped after boot and that is normal

    If WdFilter, WdNisDrv, WdNisSvc, or WinDefend are stopped, continue with the reset steps below.

    1. Rule out malware first. Run Microsoft Safety Scanner.
    2. Do not install a third-party antivirus unless necessary. If any non-Microsoft antivirus is installed, uninstall it first. On Windows 10 and Windows 11, a non-Microsoft antivirus can cause Microsoft Defender Antivirus to be turned off automatically, or to run in passive mode when Defender for Endpoint is present.
    3. Reset Defender definitions and platform. Open an elevated Command Prompt and run:
    MpCmdRun.exe -RemoveDefinitions -All
    MpCmdRun.exe -ResetPlatform
    
    1. Back up Defender policy settings before removing them. This is a registry change. Incorrect changes can affect security settings. In an elevated PowerShell session, run:
    New-Item -Path "C:\DefenderTemp" -ItemType Directory; Invoke-Command {reg export 'HKLM\SOFTWARE\Policies\Microsoft\Windows Defender' C:\DefenderTemp\_DefenderAVBackup.reg}
    
    1. Remove Defender policies that may be forcing it off. This is a registry change. Incorrect changes can affect security settings. In an elevated PowerShell session, run:
    Remove-Item -Path 'HKLM:\SOFTWARE\Policies\Microsoft\Windows Defender' -Force
    
    1. Run Microsoft Update after the reset. The documented resolution includes updating after the platform reset.
    2. If scans still fail near the end, check whether the issue is tied to update or engine errors. Documented guidance for repeated Defender scan errors is to:
    • run Windows Update
    • try installing the latest protection updates manually
    • submit feedback through Feedback Hub if the issue continues
    1. If the service still shows as stopped in Windows Security but appears running in services.msc, check for policy or compatibility causes. Generate a Group Policy report from an elevated Command Prompt:
    GPresult.exe /h gpresult.html
    

    Then review gpresult.html for:

    • Turn off Microsoft Defender Antivirus = Enabled
    • DisableAntiSpyware under HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows Defender

    If those are present, Defender may be disabled by policy rather than failing normally.

    1. If the service cannot be started cleanly from Services, try the documented service check flow:
    • open services.msc
    • select Windows Defender Antivirus Service
    • confirm Startup Type is Automatic
    • use Action > Start
    • if Start is unavailable, use Stop, wait for it to stop, then use Start again

    If an error appears during that process, collect the exact error text.


    AI-generated content may be incorrect. Read our transparency notes for more information.

    Was this answer helpful?